{"searchId":"602e3f71-cf8b-4396-ad70-bfbdc20a8afc","leads":[{"id":"reddit-878994684","title":"Advice on kitchen faucet replacement and how far to take it.","summary":"We've lived in our 70s vintage home for about seven years but the kitchen sink and everything associated with it are, I think, much older. There are signs that major kitchen renovations were done circa 1990, so some of the existing plumbing might be 35 years old. The water lines are PEX lines, if that tells you anything. (Or, at least I'm assuming it's PEX. It's plastic lines with those metal clamps) The kitchen faucet is leaking a bit - a slow seeping drip down below the faucet creating a puddl","platform":"Reddit","score":80,"outreachMessage":"Hi — I saw your post, “Advice on kitchen faucet replacement and how far to take it.”. If this is still active, please share the best way to discuss the project and any timing or scope details.","location":"Dallas, TX","postedAt":"8h ago","minutesAgo":485,"contactInfo":"Reply via the linked Reddit post | 💡 DM with your local rate and availability — first to respond wins","sourceUrl":"https://www.reddit.com/r/Plumbing/comments/1xiefju/advice_on_kitchen_faucet_replacement_and_how_far/","jobDetails":"⚡ Today","urgency":"high"},{"id":"reddit-209488836","title":"Plumber says water heater flue installation is fine, but home inspector flagged it. Is this a concern?","summary":"A plumber from Stack came out and, after consulting his boss, didn’t seem concerned. They could correct it, which would require going into the attic. But, again, he didn’t seem to think it was a problem and said there isn’t any code for it. I know nothing about this stuff. So is the clearance shown actually a problem? Is it a fire hazard? Do I need to bother getting this repair done? Edit- adding photo: up close of pipe to ceiling submitted by /u/bluesky675 [link] [comments]","platform":"Reddit","score":80,"outreachMessage":"Hi — I saw your post, “Plumber says water heater flue installation is fine, but home inspector flagged it. Is this a concern?”. If this is still active, please share the best way to discuss the project and any timing or scope details.","location":"Dallas, TX","postedAt":"3d ago","minutesAgo":4376,"contactInfo":"Reply via the linked Reddit post | 💡 DM with your local rate and availability — first to respond wins","sourceUrl":"https://www.reddit.com/r/Plumbing/comments/1xg0h6o/plumber_says_water_heater_flue_installation_is/","jobDetails":null,"urgency":"critical"},{"id":"reddit-180117175","title":"This educational LEGO Ideas model called \"The Urban Water Cycle\" shows the urban journey of water. The display set also","summary":"The model on LEGO Ideas: https://ideas.lego.com/product-ideas/da2876b0-2f99-4279-abe1-6d32e1ccfe85 The project is being endorsed by numerous water associations around the world, including EurEau, the European Water Association (EWA), Svenskt Vatten (Sweden), VSA (Switzerland), IGWP (Poland), ÖWAV (Austria), Norsk Vann (Norway), EVEL (Estonia), the Australian Water Association (AWA), Western Canada Water, and the National Rural Water Association (NRWA). submitted by /u/BrickNoire [link] [comments","platform":"Reddit","score":78,"outreachMessage":"","location":"Dallas, TX","postedAt":"2h ago","minutesAgo":145,"contactInfo":"Reply via the linked Reddit post | 💡 DM with your local rate and availability — first to respond wins","sourceUrl":"https://www.reddit.com/r/Plumbing/comments/1xil8br/this_educational_lego_ideas_model_called_the/","jobDetails":"⚡ Today","urgency":"medium"},{"id":"reddit-1767223121","title":"Compression valve will not go on a 1/2 inch copper pipe tightly and securely. Soldered/sweated chrome escutcheon decorat","summary":"Hello, I am having an issue putting a compression threaded quarter turn angle valve on this 1/2 inch pipe in order to connect my toilet. The issue is that it won’t go on securely and is moving slightly where it will leak. I am using the correct size valve of 1/2 inlet diameter by a 3/8 outlet diameter. I was told by a plumber to remove the decorative chrome sleeve on the pipe that is in the way and it is not coming off with propane. Does anyone know what else I can try to get a compression valve","platform":"Reddit","score":76,"outreachMessage":"Hi — I saw your post, “Compression valve will not go on a 1/2 inch copper pipe tightly and securely. Soldered/sweated chrome escutcheon decorat”. If this is still active, please share the best way to discuss the project and any timing or scope details.","location":"Dallas, TX","postedAt":"1d ago","minutesAgo":2658,"contactInfo":"Reply via the linked Reddit post | 💡 DM with your local rate and availability — first to respond wins","sourceUrl":"https://www.reddit.com/r/Plumbing/comments/1xh3ogy/compression_valve_will_not_go_on_a_12_inch_copper/","jobDetails":null,"urgency":"high"},{"id":"reddit-270826743","title":"Compression valve will not go on a 1/2 inch copper pipe tightly and securely. Soldered/sweated chrome escutcheon decorat","summary":"Hello, I am having an issue putting a compression threaded quarter turn angle valve on this 1/2 inch pipe in order to connect my toilet. The issue is that it won’t go on securely and is moving slightly where it will leak. I am using the correct size valve of 1/2 inlet diameter by a 3/8 outlet diameter. I was told by a plumber to remove the decorative chrome sleeve on the pipe that is in the way and it is not coming off with propane. Does anyone know what else I can try to get a compression valve","platform":"Reddit","score":76,"outreachMessage":"Hi — I saw your post, “Compression valve will not go on a 1/2 inch copper pipe tightly and securely. Soldered/sweated chrome escutcheon decorat”. If this is still active, please share the best way to discuss the project and any timing or scope details.","location":"Dallas, TX","postedAt":"1d ago","minutesAgo":2665,"contactInfo":"Reply via the linked Reddit post | 💡 DM with your local rate and availability — first to respond wins","sourceUrl":"https://www.reddit.com/r/Plumbing/comments/1xh3hy8/compression_valve_will_not_go_on_a_12_inch_copper/","jobDetails":null,"urgency":"high"}],"industry":"Plumbing","location":"Austin, TX","generatedAt":"2026-10-29T16:42:12.183Z","remaining":3,"isPro":false,"tier":"free","leadsignal_quota":{"tier":"free","limit":3,"remaining":3,"resets_at":"2026-10-30T00:00:00.000Z"},"agentLevel":"rookie","searchCount":0,"resetsAt":"2026-10-30T00:00:00.000Z"}